Marine Division · Bellingham, WA Mon–Thu 7:30 am–4:30 pm · Fri closed Questions? (360) 734‑8509 · Send us a message
Coastline Equipment, Marine Division - home Estimate (0)
Measure Twice, Weld Once

How to measure for your tank

A tank built to the wrong numbers is the one problem we can't fix after the fact. We build to exactly what you submit, and this page helps you get those numbers right.

Read this first: your tank is built to exactly the dimensions you submit, to a fabrication tolerance of ±1/8″. We don't guess at your numbers or quietly adjust them. If a tank built to your dimensions doesn't fit the space, that's a measuring problem the shop can't absorb. Spend ten careful minutes here before you order.

Body dimensions only

Every dimension you enter describes the tank shell only. Do not include:

  • Filler neck, vent, or fitting height: fittings sit above the body, and how far up depends on where the fill goes. The lowest we can get is 1-1/2″, using an Almar fill on the edge of the tank. A fill inboard on the top needs 2-1/4″ minimum. Then add the thickness of your own hose and clamp on top of that. People forget this step, and it's what puts a filler neck into a deck lid. If overhead space is tight, tell us and we'll work the fill location around it.
  • Mounting tabs: tabs add width beyond the body, but there's no standard size to plan around. We add them by request or because they're part of an existing design, and we work out the layout with you on the drawing. If your compartment is tight and you need tabs, raise it early so the tab width comes out of the tank body rather than your clearance.
  • Clearance: the gap between tank and compartment is your deduction to make, not something we add.

General rules

  1. Measure in inches, with a real tape measure, not from memory or a brochure.
  2. Measure the compartment, not the old tank, unless you're certain the old tank fit well and comes out easily.
  3. Leave at least 1/4″ clearance in every direction. A snug tank is hard to install, hard to remove, and chafes.
  4. Check what the tank must pass by on its way in: deck openings, hatch lips, stringers, hoses, wiring. A tank that fits the compartment but can't get into it is no use. Check the entry path at the angle the tank will take.
  5. Watch for sloped floors, bulkheads, and bracing. Measure the smallest usable box, not the biggest.
  6. Leave room for hose routing and future removal. Fills, vents, and senders need hose bend radius above them.

Dimension definitions

DimensionWhat it means
LengthThe longest dimension, end to end.
WidthSide to side, viewed from above.
HeightBody height only: bottom of tank to top of tank, no fittings.
Shape extras Vee depth, belly drop/bottom width, taper widths, outboard height. Each shape's page and the builder label which measurement is which, next to the live drawing.

Mockups: plywood, not cardboard

If you want to prove the fit before ordering, build the mockup from rigid plywood or foam board. Cardboard flexes. It will squeeze into a space the metal tank cannot, and give you a false pass. If the plywood box goes in and out cleanly with clearance to spare, your numbers are right.

Common mistakes we hear from customers

  • “I measured my old tank.” The old tank that was a nightmare to remove? Its dimensions are the reason. Measure the compartment and subtract clearance.
  • “I forgot the tabs.” Mounting tabs add width. If the compartment fits the body exactly, it doesn't fit the tank.
  • “It fit, until I closed the lid.” Filler neck height above the body is real height. Measure to the underside of whatever closes above the tank.
  • “I figured you'd call if something looked off.” We build what you approve on the drawing. Drawing approval is where to catch anything that looks off, so check every number on it.

Drawings

For standard shapes, the builder generates the dimensioned drawing for you, and you only mark the fitting locations. For custom shapes or markups, see the drawing examples for what a buildable submission looks like.

The fine print: Coastline Equipment is not responsible for fitment problems caused by incorrect or incomplete customer measurements. This page is here so it doesn't become your problem either.